Tag Archives: sportsbike

Yamaha YZF R1 Engine rebuild with pictures, part 1 of 3

We have a Yamaha R1 in that was, unfortunately, run with little or no oil, as as we all know, it could cause catastrophic damage to the engine internals, as the oil lubricates all the internals.

This blog post is part 1 of three – as the project can be divided into three parts (and the blog posts will be divided likewise). Stage 1 is the disassembly, and diagnosis, Stage 2 is the actual repair and stage 3 assembly and testing. If we make other discoveries or realise the extent of damages are far worse than we imagined, this structure may have to change.

Firstly we went to get the bike on the bench and start stripping it down. The engine was not run after we had learnt that it had been ran with little or no oil, but we turned it by hand to check for strange noises, and indeed, it was a little rough and  sure enough, there was a knocking sound! Didn’t sound good at all.

P1080875

First step was to turn the engine by hand to check for any potential damages. It was pretty rough and didn’t feel right.

P1080877

We then proceeded to removal of the engine from the frame. Several skinned knuckles and some help from another technician and the heart of the beast was plucked from its torso!

The next few pictures show the engine disassembly, to look and see where the problem was.

P1080878

Engine on the bench.

P1080879

And we started off from the clutch side.

P1080880

Proceeding onto the sump, to check for any lumps or debris caused by bits grinding or breaking off.

P1080882

A closer look at the clutch side.

P1080890

Removed the pump to check the gearbox for anything out of place.

P1080895

We then went on to dismantle the crankcase upper and lower sections, to check the actual crankshaft itself.

P1080903

Crankshaft removed, with bearing shells on the right hand side of the picture (on a shop towel).

P1080905

The shells did look battered and abnormally worn. Along with the channels that the shells sit in. The crankshaft also had some damage too.

P1080921

The pistons and conrods were, thankfully, saved. Had the engine been run for any longer, the build would have been taken to another level, of work, and expense!

We then checked over the rest of the parts, as below, and thankfully, nothing much to report here;

P1080920

Piston bores were fine,
P1080916

As was the top end and head, valves etc.
P1080915

The  camshafts are another delicate part, and damages to these could be costly, and if gone unnoticed, it could really ruin your day! We removed these and checked for run-out and ensures all the cam lobes were smooth and as intended by the manufacturer.

The damaged crankshaft has been sent to a good friend of ours, and an expert with engine internals and engine building, for repair. We will post up part two when it arrives.

Take care for now!

Ali

London and Herts motorcycle trader business now open

We have just started a new side to the business, and info can be found on our bike trading website – dealing with both trade and public.

You can see the site as it is now on http://motorcycletradersuk.co.uk/ - it will go through a few design steps and development so watch this space.

we want your bike

Primarily, it is a universal outlet for your motorcycles; whether you are a private individual, or a trade seller.

We are happy to buy it if you have been offered peanuts for your part exchange, or are looking to trade it in with any of our stock.

If it is an MoT failure, or an older bike sat there and you want rid of it, give us a call.

Otherwise, if it a new, modern machine, and you are simply selling it, but fed up with time-wasters and want a quick sale, give us a call on our usual number, 01707 66 33 44.

We offer quick cash, and immediate collection.